SCI-ART LAB

Science, Art, Litt, Science based Art & Science Communication

About correcting aberrations of optical systems and artistic forms in the Readymades class

About correcting aberrations of optical systems and artistic forms in the Readymades class

 

  I come back to the discussed artistic forms of science, which

belong to the Readymades class evidenced by Marcel Duchamp.

 

 

Extract from Wikipedia

Readymades[edit]

Main article: Readymades of Marcel Duchamp

"Readymades" were found objects which Duchamp chose and presented as art. In 1913, Duchamp installed a Bicycle Wheelin his studio. However, the idea of Readymades did not fully develop until 1915. The idea was to question the very notion of Art, and the adoration of art, which Duchamp found "unnecessary".[31]

 

I copy from a commercial presentation section through a camera lens

 

 It is interesting to point out some theoretical aspects that come from the scientific substrate that generates such forms,

respectively programs for optical computing.

 

It has been an effective theoretical basis for photographic objectives, formed over 200 years.

 

A historical example extracted from Wikipedia

 

 He came up with the Petzval Portrait (modern Austria) in 1840, a four-element lens consisting of a front-cemented achromat and a rear air-spaced achromat that, at f/3.6, was the first wide-aperture portrait lens. It was appropriate for one- to two-minute shaded outdoors daguerreotype exposures. With the faster collodion (wet plate)

 

 

Optical computing programs have been perfected gradually, reaching the automatic calculation of aberration corrections,

such as zemax programs

  Although these programs are very useful, their application is conditional. I give below extracted from

   articles published by specialists in the field that have been written over the last decade.

 

  Thus, in relation to correction steps, account must be taken of the conditions of use

  for each product class.

 

  Excerpts

 

Achromat, Apochromat, Superachromat – What is the Difference ...
l./achromat-apochromat-superachromat-what-is-the-difference/

 

by Dr. Hannfried Zügge, (CZ)

...............................

However, the secondary spectrum features - firstly - a typical profile and - secondly - a typical magnitude, depending to a large extent on the focal length and the lens type. The longer the focal length and the larger the aperture (speed) of the lens, the more the image quality will be impaired by the secondary spectrum. This can be so severe that the secondary spectrum is the main factor limiting the image quality.

Hence, the next step required by the optical designer is to also correct the secondary spectrum in these cases. The result is the apochromat. The only aid available for this purpose is the use of very special optical materials: long-crown glass (fluor crown glass and calcium fluoride) and special short flint glass. These can therefore be justifiably called extreme types of glass, since they not only display an unusual behavior with regard to the relative partial dispersion, but are also extremely expensive and difficult to process.
........................

And relative to the fact that the use of ZEMAX automated programs should be done after corrections have been made

preliminary with lens bending optimization programs

 

Design and Correction of optical Systems

 

In the same book you see and;

ODZ_Optical design with Zemax 11 Correction I.pdf

 

 

So before the Zemax program is used, a preliminary correction is required

(11 Corection I) where the concept of lens bending appears.

 

   I practice the profession of manufacturer of optical devices including computer, optical systems,

  I have also studied the basics of optical computing.

  In the specialized articles written in the last century, the Lens Bending method was described as being

  based on the aberrations of the optical systems.

 

  Lens Bending is the method by which lens power is retained

modifying the bend radii by computing.

 

   Decades ago I designed a program to automatically minimize optical systems

using the Lens Bending technique

  I recently published in ResearchGate details of the algorithm I used

 

Link:

Bending method for automatic optical aberations correction

 

 

Views: 71

Replies to This Discussion

Limits to automatic correction, ZEMAX applied to aberrations of optical systems

 

RSS

© 2017   Created by Dr. Krishna Kumari Challa.   Powered by

Badges  |  Report an Issue  |  Terms of Service